Prism
Pole Top Shoe, Standard Base - Item
No. 81-0871
- Precision
machined aluminum body with 1” (25.4 mm) base
- 5/8-11
female thread
- Height:
3.37 in (85.6 mm)
Prism
Pole Top Shoe, Wide Base - Item
No. 81-0870
- Precision
machined aluminum body with 1” (25.4 mm) base
- 5/8-11
female thread
- Height:
3.37 in (85.6 mm)
Range/Prism
Pole Shoe - Item
No. 81-0872
- 3.37
inch steel body, steel body
- Weighs
0.30 lbs. (0.14 kg)
Double
Male Adapter - Item
No. 81-0873
- Double
Male 5/8 x 11 adapter
- Weighs
0.06 lbs. (0.03 kg)
Bipod
Leg Clip - Item
No. 81-0875
The
bipod leg clip easily attaches to the base of any 1.25 inch O.D. prism or
antenna pole. The
bipod legs snap into the clip making the system convenient for transport or
storage.
- Weighs
0.04 lbs. (0.02 kg)
Pole
Peg Adjusting Jig - Item
No. 81-0876
Convenient
for adjusting and calibrating pole vials in the office. The
adjusting jig features an ‘L-bracket’ to rest the prism pole point on and the
adjustable top piece.
Use
the adjustable top to center your pole before adjusting the bubble.
- Weighs
1.00 lbs. (0.45 kg)
Topo-Boot - Item
No. 81-0877
The
TopoBoot®, made of black nylon, screws over the precision point and increases
the area of the point for use on soft surfaces in topo shots.
The Topo-Boot is
removable and stores conveniently under the large, easy-to read vial.
- Weighs
0.05 lbs. (0.02 kg)
Aluminum
Point and Steel Tip - Item
No. 81-0878
- 3.37" (85.6 mm) aluminum prism pole point with steel tip
- Weighs
0.01 lbs. (0.004 kg)
Mounting Instructions for Prism Pole
Adjusting Bracket:
Place an extra tip (std. point) on the top of the longest
pole you will be adjusting. Measure the low rod length... point to point. Add
three inches to this measurement. This will be the distance from the upper to
the lower bracket.
Determine where on the wall you want the brackets located.
Mark where you want the top of the lower bracket to be. Using the point-to-point
distance plus the three inches... measure up and mark where the top of the
upper bracket is to be located.
Hold the top of the upper bracket with the hole up and the
same sized holes against wall and mark where the top screw attaches to the
wall. Drill one pilot hole initially.
Attach the upper bracket by the top hole. Do not fully
tighten! Place a carpenter's level on the top of the bracket parallel to the
wall and proceed to level the bracket. When it is level, fully lighten the
screw and drill a second pilot hole. Making sure the bracket remains level,
insert and fully tighten the second screw.
Put the pin with hole into the hole of the upper bracket.
Put the 'S'-hook through the hole and attach your plumb bob on the hook. Align
the hole in the lower bracket with the plumb bob tip by sliding the adjustable
bracket accordingly. Make sure to keep the bracket level. Fasten the bracket to
the wall, place the carpenter's level on the bracket, level, and fully tighten.
The hole should line up fairly well with the plumb bob, but the final alignment
will be done last. Drill the hole for the last screw. Making sure it is still
level, insert and fully tighten the last screw.
Align the hole with plumb bob by moving the articulated
portion of the lower bracket. Tighten the nut. The alignment should be stable,
but it is a good idea to check it periodically.
Adjusting
the Pole:
With an extra tip
on top of the pole, insert the bottom point into the lower alignment hole.
Extend the pole, inserting the point into the upper alignment hole (outside
hole). Be sure you extend it with a little pressure, so the pole is securely held
by the bracket. It should be snug but rotate freely.
Once the pole is secure... center
bubble vial by adjusting the Allen screws below the bubble housing. Next turn the pole 180 degrees... if the bubble is still centered... your
calibration is complete.
If the bubble is out of center... you need to take out half the error by using
the adjusting screws... turn the pole back 180 degrees... center bubble and go
through the adjustment procedure until the bubble is centered. Once this is
done... bubble should be centered on all four sides.
El Montaje de Instrucciones para Polo{polaco} de Prisma que Ajusta Soporte:
Los · Colocan una punta{un consejo} suplementaria (std. punto) en la cumbre del poste más largo que usted ajustará. Mida la longitud de vara{barra} baja ... punto para señalar. Añada tres pulgadas a esta medida. Este será la distancia del superior al soporte inferior.
Los · Determinan donde en la pared usted quiere los soportes localizados. La marca donde usted quiere que la cumbre del soporte inferior sea. Usando el punto para señalar distancia más tres pulgadas los ... están a la altura y marca donde la cumbre del soporte superior debe ser localizada.
Los · Sostienen la cumbre del soporte superior con el agujero y los mismos agujeros clasificados contra pared y marca donde el tornillo superior adjunta a la pared. Taladre un agujero piloto al principio.
Los · Adjuntan el soporte superior por el agujero superior. ¡No apriétese totalmente! Coloque el nivel de un carpintero en la cumbre de la paralela de soporte a la pared y póngase a nivelar el soporte. Cuando esto es el nivel, totalmente iluminar el tornillo y taladrar un segundo agujero piloto. Asegurándose el soporte permanece el nivel, el encarte y totalmente apretar el segundo tornillo.
• Puesto el alfiler con agujero en el agujero del soporte superior. Ponga 'el S'-gancho por el agujero y adjunte su plomo en el gancho. Alinee el agujero en el soporte inferior con la punta{el consejo} de plomo deslizando el soporte ajustable en consecuencia. Asegúrese para guardar el nivel de soporte. Sujete el soporte a la pared, coloque el nivel del carpintero en el soporte, nivel, y totalmente apriétese. El agujero debería alinearse justamente bien con el plomo, pero la alineación final será hecha última. Taladre el agujero para el último tornillo. Asegurándose esto es todavía el nivel, el encarte y totalmente apretar el último tornillo.
Los · Alinean el agujero con el plomo moviendo la parte articulada del soporte inferior. Apriete la tuerca. La alineación debería ser estable, pero esto es una idea buena de comprobarlo periódicamente.
Adusting el Polo{polaco}:
Con una punta{un consejo} suplementaria encima del poste, inserte el punto de fondo en el agujero de alineación inferior. Amplíe el poste, insertando el punto en el agujero de alineación superior (fuera del agujero). Esté seguro que usted lo amplía con una pequeña presión entonces el poste es bien sostenido por el soporte. Debería ser cómodo, pero girar libremente.
• Una vez que el poste es el frasco de burbuja de centro de ... seguro ajustando los tornillos de allen debajo del alojamiento de burbuja.
• Después giran el poste 180 grados ... si la burbuja todavía es centrada ... su calibración es completa.
• Si la burbuja es fuera del centro ... usted tiene que sacar la mitad el error usando los tornillos que se adaptan ... gira el poste atrás 180 grados ... centro burbujean y pasan por el procedimiento de ajuste hasta que la burbuja sea centrada. Una vez que este es hecho la burbuja de ... debería ser centrada en cuatro lados.